89
[Sysname-Vlan-interface10] ospf cost 65
Related commands
bandwidth-reference
ospf database-filter
Use
ospf database-filter
to filter outbound LSAs on an interface.
Use
undo ospf database-filter
to restore the default.
Syntax
ospf database-filter
{
all
|
{
ase
[
acl ipv4-acl-number
]
|
nssa
[
acl
ipv4-acl-number
]
|
summary
[
acl ipv4-acl-number
]
}
*
}
undo ospf database-filter
Default
The outbound LSAs are not filtered on the interface.
Views
Interface view
Predefined user roles
network-admin
Parameters
all
: Filters all outbound LSAs except the Grace LSAs.
ase
: Filters outbound Type-5 LSAs.
nssa
: Filters outbound Type-7 LSAs.
summary
: Filters outbound Type-3 LSAs.
acl ipv4-acl-number
: Specifies an IPv4 ACL by its number in the range of 2000 to 3999.
Usage guidelines
When you specify an ACL, follow these guidelines:
•
If a rule in the specified ACL is applied to a VPN instance, the rule does not take effect.
•
If a rule in the specified ACL is not applied to any VPN instance, the rule takes effect on both
VPN packets and public-network packets.
To use an advanced ACL (with a number from 3000 to 3999) in the command, configure the ACL
using one of the following methods:
•
To deny/permit LSAs with the specified link state ID, use the
rule
[
rule-id
]
{
deny
|
permit
}
ip source
sour-addr sour-wildcard
command.
•
To deny/permit LSAs with the specified link state ID and mask, use the
rule
[
rule-id
]
{
deny
|
permit
}
ip source
sour-addr sour-wildcard
destination
dest-addr dest-wildcard
command.
The
source
keyword specifies the link state ID of an LSA and the
destination
keyword
specifies the subnet mask of the LSA. For the mask configuration to take effect, specify a contiguous
subnet mask.
If the neighbor has already received an LSA to be filtered, the LSA still exists in the LSDB of the
neighbor after you execute the command.
Summary of Contents for SOHO IE4300
