31
Views
System view
Predefined user roles
network-admin
Parameters
agent
: Specifies an LLDP agent type. If you do not specify an agent type, this command applies to
the nearest bridge agent.
•
nearest-customer
: Specifies the nearest customer bridge agent.
•
nearest-nontpmr
: Specifies the nearest non-TPMR bridge agent.
ipv6
: Specifies an IPv6 management address. If you do not specify this keyword, an IPv4
management address will be advertised.
ip-address
: Specifies the management address to be advertised.
interface
loopback
interface-number
: Specifies a loopback interface by its number in the
range of 0 to 127. The IP address of the loopback interface will be advertised as the management
address. The value range for the
interface-number
argument is 0 to 127.
interface m-gigabitethernet interface-number
: Specifies an M-GigabitEthernet
interface by is number. The IP address of the M-GigabitEthernet interface will be advertised as the
management address.
interface vlan-interface interface-number
: Specifies a VLAN interface by is number
in the range of 1 to 4094. The IP address of the VLAN interface will be advertised as the
management address.
Usage guidelines
If you execute this command multiple times, the most recent configuration takes effect.
You can configure advertisement of the management address TLV globally or on a per-interface
basis. The device selects the management address TLV advertisement setting for an interface in the
following order:
1.
Interface-based setting, configured by using the
lldp tlv-enable
command with the
management-address-tlv
keyword.
2.
Global setting, configured by using the
lldp global tlv-enable basic-tlv
management-address-tlv
command.
3.
Default setting for the interface.
By default:
The nearest bridge agent and nearest customer bridge agent advertise the management
address TLV.
The nearest non-TPMR bridge agent does not advertise the management address TLV.
The IPv4 or IPv6 address of the LLDP frame sending port will be advertised as the management
address when the following conditions exist:
•
The
ip-address
argument is not configured.
•
The specified loopback interface, M-GigabitEthernet interface, or VLAN interface does not have
an IPv4 or IPv6 address, or the specified interface does not exist.
If the LLDP frame sending port does not have an IPv4 or IPv6 address, the MAC address of the port
will be advertised.
If you specify the
ipv6
keyword, the management address is the IPv6 address. If you do not specify
the
ipv6
keyword, the management address is the IPv4 address.
Summary of Contents for SOHO IE4300
