54
Usage guidelines
You cannot edit a reaction entry after it is created. To change the attributes in a reaction entry, use
the
undo reaction
command to delete the entry, and then configure a new one.
Only successful probe packets are monitored. Statistics about failed probe packets are not collected.
No actions can be configured for a reaction entry of monitoring one-way delays. To display the
monitoring results and statistics, use the
display nqa reaction counters
and
display nqa
statistics
commands.
Examples
# Create reaction entry 1 for monitoring the destination-to-source delay of every UDP jitter packet,
and set the upper limit to 50 milliseconds and lower limit to 5 milliseconds. Before the NQA operation
starts, the initial state of the reaction entry is invalid. The destination-to-source delay is calculated
after the response to the probe packet arrives. If the delay exceeds the upper limit, the state of the
reaction entry is set to over-threshold. If it is below the lower limit, the state is set to below-threshold.
Once the state of the reaction entry changes, a trap message is generated and sent to the NMS.
<Sysname> system-view
[Sysname] nqa entry admin test
[Sysname-nqa-admin-test] type udp-jitter
[Sysname-nqa-admin-test-udp-jitter] reaction 1 checked-element owd-ds threshold-value 50
5
reaction checked-element icpif
Use
reaction checked-element icpif
to configure a reaction entry for monitoring the ICPIF
value in the voice operation.
Use
undo reaction
to delete a reaction entry.
Syntax
reaction
item-number
checked-element
icpif
threshold-value
upper-threshold lower-threshold
[
action-type
{
none
|
trap-only
}
]
undo reaction item-number
Default
No reaction entries for monitoring ICPIF values exist.
Views
Voice operation view
Predefined user roles
network-admin
Parameters
item-number
: Assigns an ID to the reaction entry, in the range of 1 to 10.
threshold-value
: Specifies threshold range.
upper-threshold
: Specifies the upper limit in the range of 1 to 100.
lower-threshold
: Specifies the lower limit in the range of 1 to 100. It must not be greater than
the upper limit.
action-type
: Specifies what action to be triggered. The default action is
none
.
none
: Specifies the action of displaying results on the terminal display.
Summary of Contents for SOHO IE4300
