30
[Sysname] interface gigabitethernet 1/0/1
[Sysname-GigabitEthernet1/0/1] jumboframe enable
link-delay
Use
link-delay
to set the physical state change suppression interval on an Ethernet interface.
Use
undo link-delay
to restore the default.
Syntax
link-delay
{
down
|
up
}
[
msec
]
delay-time
undo link-delay
{
down
|
up
}
Default
Each time the physical link of a port goes up or comes down, the interface immediately reports the
change to the CPU.
Views
Ethernet interface view
Predefined user roles
network-admin
Parameters
down
: Suppresses link-down events.
up
: Suppresses link-up events.
msec
: Enables the physical state change suppression interval to be accurate to milliseconds. If you
do not specify this keyword, the suppression interval is accurate to seconds.
delay-time
: Sets the physical state change suppression interval on the Ethernet interface. A
value of 0 means that physical state changes are immediately reported to the CPU and are not
suppressed.
•
If you do not specify the
msec
keyword, the value range is 0 to 30 seconds.
•
If you specify the
msec
keyword, the value range is 0 to 10000 milliseconds, and the value must
be a multiple of 100.
Usage guidelines
You can configure this feature to suppress only link-down events, only link-up events, or both. If an
event of the specified type still exists when the suppression interval expires, the system reports the
event.
When you configure this feature, follow these guidelines:
•
To suppress link-down events, configure the
link-delay
down
command.
•
To suppress link-up events, configure the
link-delay up
command.
On an interface, you can configure different suppression intervals for link-up and link-down events. If
you execute the
link-delay
command multiple times on an interface, the following rules apply:
•
You can configure the suppression intervals for link-up and link-down events separately.
•
If you configure the suppression interval multiple times for link-up or link-down events, the most
recent configuration takes effect.
Do not execute this command on an interface that has RRPP, spanning tree protocols, or Smart Link
enabled.
Summary of Contents for SOHO IE4300
