90
Usage guidelines
The address option or the hostname option specifies the peer with which the device can use the
preshared key to perform IKE negotiation.
Two peers must be configured with the same preshared key to pass preshared key authentication.
In FIPS mode, if you do not specify the
cipher string
option, you specify a plaintext preshared
key in interactive mode. The key is a case-sensitive string of 15 to 128 characters, and it must
contain uppercase and lowercase letters, digits, and special characters other than the question mark
(?). In non-FIPS mode, this command does not support configuring a preshared key in interactive
mode.
Examples
# Create IKE keychain
key1
and enter IKE keychain view.
<Sysname> system-view
[Sysname] ike keychain key1
# Set the preshared key to be used for IKE negotiation with peer 1.1.1.2 to
123456TESTplat&!
.
[Sysname-ike-keychain-key1] pre-shared-key address 1.1.1.2 255.255.255.255 key simple
123456TESTplat&!
Related commands
authentication-method
keychain
priority (IKE keychain view)
Use
priority
to specify a priority for an IKE keychain.
Use
undo priority
to restore the default.
Syntax
priority
priority
undo priority
Default
The priority of an IKE keychain is 100.
Views
IKE keychain view
Predefined user roles
network-admin
Parameters
priority
priority
: Specifies a priority number in the range of 1 to 65535. The lower the priority
number, the higher the priority.
Usage guidelines
To determine the priority of an IKE keychain, the device examines the existence of the
match
local address
command before examining the priority number. An IKE keychain with the
match
local address
command configured has a higher priority than an IKE keychain that does not
have the
match local address
command configured.
Examples
# Set the priority to 10 for IKE keychain
key1
.
Summary of Contents for SOHO IE4300
