15
Field
Description
Last time when physical state changed
to up
Last time when the physical state of the interface changed to up.
If the time zone is configured, this field is in the YYYY/MM/DD
HH:MM:SS
zone-name
±HH:MM:SS format, where the
zone-name
argument is the local time zone.
A hyphen (-) indicates that the physical state of the interface has
never changed.
Last time when physical state changed
to down
Last time when the physical state of the interface changed to
down.
If the time zone is configured, this field is in the YYYY/MM/DD
HH:MM:SS
zone-name
±HH:MM:SS format, where the
zone-name
argument is the local time zone.
A hyphen (-) indicates that the physical state of the interface has
never changed.
Last 300 seconds input: 0 packets/sec
0 bytes/sec 0%
Last 300 seconds output: 0 packets/sec
0 bytes/sec 0%
Average inbound or outbound traffic rate (in pps and Bps) in the
last 300 seconds, and the ratio of the actual rate to the interface
bandwidth.
A hyphen (-) indicates that the statistical item is not supported.
Input(total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0
multicasts, 0 pauses
The two fields on the first line represent the inbound traffic
statistics (in packets and bytes) for the interface. All inbound
normal packets, abnormal packets, and normal pause frames
were counted.
The four fields on the second line represent:
•
Number of inbound unicast packets.
•
Number of inbound broadcasts.
•
Number of inbound multicasts.
•
Number of inbound pause frames.
A hyphen (-) indicates that the statistical item is not supported.
Input(normal): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0
multicasts, 0 pauses
The two fields on the first line represent the inbound normal traffic
and pause frame statistics (in packets and bytes) for the interface.
The four fields on the second line represent:
•
Number of inbound normal unicast packets.
•
Number of inbound normal broadcasts.
•
Number of inbound normal multicasts.
•
Number of inbound normal pause frames.
A hyphen (-) indicates that the statistical item is not supported.
input errors
Statistics of incoming error packets.
runts
Number of inbound frames meeting the following conditions:
•
Shorter than 64 bytes.
•
In correct format.
•
Containing valid CRCs.
giants
Number of inbound giants. Giants refer to frames larger than the
maximum frame length supported on the interface.
For an Ethernet interface that does not permit jumbo frames, the
maximum frame length is as follows:
•
1518 bytes (without VLAN tags).
•
1522 bytes (with VLAN tags).
For an Ethernet interface that permits jumbo frames, the
maximum Ethernet frame length is set when you configure jumbo
frame support on the interface.
Summary of Contents for SOHO IE4300
