12
start
: Monitors the specified process for start events. EAA executes the policy when the monitored
process starts.
name
process-name
: Specifies a user-mode process by its name. The process can be one that is
running or not running. If you do not specify a name, this command monitors all use-mode
processes.
instance
instance-id
: Specifies a process instance ID in the range of 0 to 4294967295. The
instance ID can be one that has not been created yet. If you do not specify an instance, EAA
monitors all instances of the process.
slot
slot-number
: Specifies an IRF member device by its member ID. If you do not specify a
member device, this command applies to the IRF fabric.
Usage guidelines
Use process event monitor policies to monitor process state changes. These changes can result
from manual operations or automatic system operations.
You can configure only one event for a monitor policy. If the monitor policy already contains an event,
the new event replaces the old event.
Examples
# Configure a CLI-defined policy to monitor all instances of the process
snmpd
for restart events.
<Sysname>system-view
[Sysname] rtm cli-policy test
[Sysname-rtm-test] event process restart name snmpd
event snmp oid
Use
event snmp oid
to configure an SNMP event for a CLI-defined monitor policy.
Use
undo event
to delete the event in a CLI-defined monitor policy.
Syntax
event snmp
oid
oid
monitor-obj
{
get
|
next
}
start-op
start-op start-val
start-val restart-op
restart-op
restart-val restart-val
[
interval
interval
]
undo event
Default
No SNMP event is configured.
Views
CLI-defined policy view
Predefined user roles
network-admin
Parameters
oid
oid
: Specifies the OID of the monitored MIB variable, a string of 1 to 256 characters.
monitor-obj
{
get
|
next
}
: Specifies the SNMP operation used for sampling variable values.
The
get
keyword represents the SNMP get operation, and the
next
keyword represents the SNMP
getNext operation.
start-op start-op
: Specifies the operator for comparing the sampled value with the start
threshold. The start threshold is crossed if the comparison result meets the condition. For keywords
available for the
start-op
argument, see
Summary of Contents for SOHO IE4300
