53
Use
undo qos car
to delete an aggregate CAR action.
Syntax
qos car car-name aggregative cir committed-information-rate
[
cbs
committed-burst-size
[
ebs excess-burst-size
]
]
[
green
action
|
red
action
|
yellow
action
]
*
qos car car-name aggregative
cir committed-information-rate
[
cbs
committed-burst-size
]
pir peak-information-rate
[
ebs excess-burst-size
]
[
green
action
|
red action
|
yellow
action
]
*
undo qos car car-name
Default
No aggregate CAR action is configured.
Views
System view
Predefined user roles
network-admin
Parameters
car-name
: Specifies the name of the aggregate CAR action. This argument must start with a letter,
and is a case-sensitive string of 1 to 31 characters.
cir
committed-information-rate
: Specifies the CIR in kbps, which is an average traffic rate.
The value range for
committed-information-rate
is 8 to 160000000.
cbs committed-burst-size
: Specifies the CBS in bytes. The value range for
committed-burst-size
is 512 to 256000000, in increments of 512. The default value for this
argument is the product of 62.5 and the CIR and must be an integral multiple of 512. When the
product is not an integral multiple of 512, it is rounded up to the nearest integral multiple of 512 that
is greater than the product. A default value greater than 256000000 is converted to 256000000.
ebs
excess-burst-size
:
Specifies the EBS in bytes.
The value range for
excess-burst-size
is 0 to 256000000, in increments of 512. If the PIR is configured, the default
EBS is the product of 62.5 and the PIR and must be an integral multiple of 512. When the product is
not an integral multiple of 512, it is rounded up to the nearest integral multiple of 512. A default value
greater than 256000000 is converted to 256000000.
pir
peak-information-rate
: Specifies the PIR in kbps. The value range for
peak-information-rate
is 8 to 160000000.
green action
: Specifies the action to take on packets that conform to CIR. The default setting is
pass
.
red action
: Specifies the action to take on the packet that conforms to neither CIR nor PIR. The
default setting is
discard
.
yellow action
: Specifies the action to take on packets that conform to PIR but not to CIR. The
default setting is
pass
.
action
: Specifies the action to take on packets:
•
discard
: Drops the packet.
•
pass
: Permits the packet to pass through.
•
remark-dot1p-pass
new-cos
: Sets the 802.1p priority value of the 802.1p packet to
new-cos
and permits the packet to pass through. The
new-cos
argument is in the range of 0
to 7.
Summary of Contents for SOHO IE4300
