4
Parameters
interface-type interface-number
: Specifies a port by its type and number, which can be a
Layer 2 Ethernet interface or Layer 2 aggregate interface.
primary
: Specifies a port as the primary port.
secondary
: Specifies a port as the secondary port.
Usage guidelines
Before configuring member ports for a smart link group, you must configure protected VLANs for the
smart link group.
Disable the spanning tree feature, RRPP, and ERPS on the ports you want to add to the smart link
group. You cannot enable the spanning tree feature, RRPP, or ERPS on a smart link group member
port.
If you configure a port as both an aggregation group member and a smart link group member, only
the aggregation group member configuration takes effect. The port is not shown in the output from
the
display smart-link group
command. The smart link group member configuration takes
effect after the port leaves the aggregation group.
You can also assign a port to a smart link group by using the
port smart-link group
command
in interface view.
Examples
# Configure GigabitEthernet 1/0/1 as the secondary port of smart link group 1.
<Sysname> system-view
[Sysname] interface gigabitethernet 1/0/1
[Sysname-GigabitEthernet1/0/1] undo stp enable
[Sysname-GigabitEthernet1/0/1] quit
[Sysname] smart-link group 1
[Sysname-smlk-group1] protected-vlan reference-instance 0
[Sysname-smlk-group1] port gigabitethernet 1/0/1 secondary
Related commands
port smart-link group
port smart-link group
Use
port smart-link group
to assign a port to a smart link group and specify the port role.
Use
undo port smart-link group
to remove a port from a smart link group.
Syntax
port smart-link group group-id
{
primary
|
secondary
}
undo port smart-link group group-id
Default
A port is not a smart link group member.
Views
Layer 2 Ethernet interface view
Layer 2 aggregate interface view
Predefined user roles
network-admin
Summary of Contents for SOHO IE4300
