Ruijie RG-S29 Series Скачать руководство пользователя страница 845

Страница: 845 / 1510

Command Reference

NSM Commands

5 NSM Commands

5.1 clear ip route

Use this command to clear the route cache.

clear ip route

{

* |

network

[

netmask

] | }

Parameter

Description

Parameter

Description

Clears all route cache.

network

Specifies the route cache of the network or subnet.

netmask

(Optional) Subnet mask. If no subnet mask is specified,

the longest match principle is used when you match

network

with the route. The cache of the longest match is

cleared.

Command

Mode

Privileged EXEC mode

Usage

Guide

Clearing route cache clears the corresponding routes and triggers the routing protocol relearning.

Please note that clearing all route cache leads to temporary network disconnection.

Examples

The following example clears the cache of the route which is the longest match with IP address

192.168.12.0.

clear ip route 192.168.12.0

Related

Commands

Command

Description

N/A

Platform

Description

N/A

5.2 ip default-gateway

Use this command to configure the default gateway IP address on 2-layer devices. Use the

default

form of this command to restore the default setting.

ip default-gateway

ip-address

no ip default-gateway

default ip default-gateway

Parameter

Description

Parameter

Description

ip-address

IPv4 address of the default gateway

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды