Ruijie RG-S29 Series Скачать руководство пользователя страница 349

Страница: 349 / 1510

Command Reference Voice VLAN Commands

Platform

Description

N/A

8.10 voice vlan security enable

Use this command to enable the Voice VLAN security mode in the global configuration mode. Use the

form of this command to disable this function.

voice vlan security enable

no voice vlan security enable

Parameter

Description

Parameter

Description

N/A

Defaults

This function is enabled by default.

Command

mode

Global configuration mode

Usage Guide

The Voice VLAN working mode can be classified into the auto-mode and the manual-mode, and

configured on the port. The working modes for the Voice VLAN on each port are independent, and

different ports can work in different working modes. In different working modes, the methods of

enabling the Voice VLAN function on the port are different. The working mode can be set according to

the IP phone type connected downward the port or the port type.

You are not recommended to transmit the voice and service data in the Voice VLAN at the same

time. But if it is necessary for you, you shall ensure that the Voice VLAN security mode has been

disabled.

In the security mode, only the source MAC addresses for the untagged packets and the packets

carried with Voice VLAN tag are checked. For other packets carried with non-voice vlan tag that

free from the Voice VLAN security/normal mode, the devices forward or discard those packets

according to the VLAN rule.

Configuration

Examples

The following example enables the Voice VLAN security mode.

Ruijie(config)# voice vlan security enable

Related

Commands

Command

Description

show voice vlan

Display Voice VLAN configurations and the

current state.

Platform

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды