Ruijie RG-S29 Series Скачать руководство пользователя страница 680

Страница: 680 / 1510

Command Reference

RIP Commands

N/A

Platform

Description

N/A

1.26 passive-interface

Use this command to disable the function of sending update packets on an interface. Use the

form

of this command to restore the default setting.

passive-interface

{

default |

interface-type interface-num

}

no passive-interface

{

default |

interface-type interface-num

}

Parameter

Description

Parameter

Description

default

Sets all interfaces to the passive interfaces.

interface-type interface-num

Indicates the interface type and number.

Defaults

Interfaces are set to the non passive interfaces by default.

Command

Mode

Routing process configuration mode

Usage Guide

The

passive-interface default

command sets all interfaces to the passive interfaces. You can use

no passive-interface

interface-type interface-num

command to set specified interfaces as

non-passive interfaces.

After you set an interface to the passive interface, RIP route update packets will no longer be sent but

can be received through the interface. In this case, route update packets can be sent to a specified

neighbor through the interfaces by using the

neighbor

command. You can use the

ip rip send

enable

and

ip rip receive enable

commands to control whether route update packets can be sent or

received through the interface.

Configuration

Examples

The following example sets all interfaces to the passive interfaces and then sets ethernet0/1 to the

non-passive interface.

Ruijie(config-router)# passive-interface default

Ruijie(config-router)# no passive-interface gigabitEthernet 0/1

Related

Commands

Command

Description

ip rip receive enable

Enables or disables receiving RIP packets on

the interface.

ip rip send enable

Enables or disables sending RIP packets on

the interface.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды