Ruijie RG-S29 Series Скачать руководство пользователя страница 1169

Страница: 1169 / 1510

Configuration Guide DHCPv6 Snooping Commands

as in air interfaces.

Configuration

Examples

The following example filters all DHCPv6 request packets on interface FastEthernet 0/1 and WLAN 1.

Ruijie# configure terminal

Ruijie(config)# interface GigabitEthernet 0/2

Ruijie(config-if-GigabitEthernet 0/2)# ipv6 dhcp snooping filter-dhcp-pkt

Ruijie(config-if-GigabitEthernet 0/2)# end

Related

Commands

Command

Description

N/A

Platform

Description

N/A

15.9 ipv6 dhcp snooping information option

Use this command to add option18/37 to the DHCPv6 request packets.

Use the

form of this command to restore the default setting.

ipv6 dhcp snooping information option

[

standard-format

]

no ipv6 dhcp snooping information option

[

standard-format

]

Parameter

Description

Parameter

Description

standard-format

The Option18/37 uses the standard format.

Defaults

This function is disabled by default.

Command

Mode

Global configuration mode

Usage Guide

With this command configured, the option18/37 will be added to the DHCPv6 request packets and the

DHCPv6 server will assign the addresses according to the option18/37 information. Use this

command without parameter

standard-format

to enable the standard format.

DHCPv6 Relay function adds option18/37 by default. Therefore, it is unnecessary to enable

functions of DHCP Snooping option18/37 and DHCPv6 Relay at the same time.

Configuration

Examples

The following example adds the option18/37 into the DHCPv6 packets.

Ruijie# configure terminal

Ruijie(config)# ipv6 dhcp snooping information option

Ruijie(config)# end

Ruijie# show ipv6 dhcp snooping

Switch DHCPv6 snooping status :ENABLE

«
...
1167
1168
1169
1170
1171
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды