Ruijie RG-S29 Series Скачать руководство пользователя страница 825

Страница: 825 / 1510

Command Reference

OSPFv3 Commands

Platform

Description

N/A

3.50 timers spf

Use this command to set the delay and interval for the OSPFv3 to calculate SPF after receiving the

topology change. Use the

format of this command to restore the default setting.

timers spf

delay holdtime

no timers spf

Parameter

Description

Parameter

Description

spf-delay

Defines the waiting time for the SPF calculation, which ranges from 0

to 2147483647 seconds. After receiving the topology change

information, the OSPF routing process has to waiting for a given

period before making the SPF calculation.

spf-holdtime

Defines the interval between two SPF calculations, which ranges

from 0 to 2147483647 seconds. If the interval has not passed even if

the waiting time has elapsed, no SPF calculation can be made yet.

Defaults

There are two default situations: 1. The versions earlier than RGOS 10.4 do not support the

command

timers throttle spf

. The system default is timers spf 5 10. 2. The RGOS 10.4 and the later

versions do support the command

timers throttle spf

, where

timer spf

takes no effect by default.

The delay for SPF calculation is subject to the default setting of the command

timers throttle spf

Refer to the description of the command.

Command

Mode

Routing process configuration mode

Usage Guide

The smaller the

spf-delay

and

spf-holdtime

, the shorter time the OSPF takes to adapt to the topology

change, but the more CPU time will be used of the router.

The

timer spf

configuration and the

timers throttle spf

configuration will overwrite each other.

Configuration

Examples

The following example sets the delay and holdtime of the OSPFv3 to 3 seconds and 9 seconds

respectively.

Ruijie(config)#

ipv6 router ospf

Ruijie(config-router)#

timers spf

3 9

Related

Commands

Command

Description

clear ipv6 ospf

Restarts part of the function of the OSPFv3.

show ipv6 ospf

Displays the OSPFv3 routing process

information.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды