Ruijie RG-S29 Series Скачать руководство пользователя страница 527

Страница: 527 / 1510

Command Reference

IPv6 Commands

3.26 ipv6 redirects

Use this command to control whether to send ICMPv6 redirect message when the switch receives

and forwards an IPv6 packet through an interface. Use the

form of this command to restore the

default setting.

ipv6 redirects

no ipv6 redirects

Parameter

Description

Parameter

Description

N/A

Defaults

This function is enabled by default.

Command

Mode

Interface configuration mode.

Usage Guide

The transmission rate of any ICMPv6 error message is limited. By default, it is 10pps.

Configuration

Examples

The following example enables ICMPv6 redirection on interface GigabitEthernet 0/1.

Ruijie(config-if-GigabitEthernet 0/1)# ipv6 redirects

Related

Commands

Command

Description

show ipv6 interface

Displays the interface information.

Platform

Description

N/A

3.27 ipv6 source-route

Use this command to forward the IPv6 packet with route header. Use the

form of this command to

restore the default setting.

ipv6 source-route

no ipv6 source-route

Parameter

Description

Parameter

Description

N/A

Defaults

The

ipv6 source-route

command is disabled by default.

Command

Mode

Global configuration mode.

Usage Guide

Because of the potential security of the header of type 0 route, it’s easy for the device to suffer from

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды