Ruijie RG-S29 Series Скачать руководство пользователя страница 898

Страница: 898 / 1510

Command Reference

Protocol-independent Configuration Commands

6.32 set ip tos

Use this command to set the tos of the IP head of the packet matching the rule in the route map

configuration mode. Use the

form of this command to remove the configured tos setting.

set ip tos

0-15

> |

max-reliability

max-throughput

min-delay

min-monetary-cost

normal

}

no set ip tos

Parameter

Description

Parameter

Description

number

Indicates the TOS value of an IP header with a number, ranging from 0

to 15.

max-reliability

max-throughput

min-delay

min-monetary-cost

normal

max-reliability |

max-throughput |

min-delay |

min-monetary-cost |

normal

Priority of an IP header.

Defaults

N/A

Command

mode

Route map configuration mode

Usage

guideline

With different TOS values for the IP packet head configured, the IP packets matching the PBR routing

are transmitted with different service qualities.

The TOS value will be specified for the head of the IP packet matched the PBR.

Examples

The following example sets the TOS value of the packet with the source IP address 192.168.217.68

received at the interface FastEthernet 0/0 as 4:

Ruijie(config)#access-list

permit

192.168.217.68 0.0.0.0

Ruijie(config)#route-map

name

Ruijie(config-route-map)#match ip address

Ruijie(config-route-map)#set ip tos

Ruijie(config)#interface FastEthernet

0/0

Ruijie(config-if)#ip policy route-map

name

Related

commands

Command

Description

match interface

Match the next-hop interface.

match ip address

Match the IP address in the ACL.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды