Ruijie RG-S29 Series Скачать руководство пользователя страница 741

Страница: 741 / 1510

Command Reference

OSPFv2 Commands

original one. Only the routes matching the specific type can be redistributed. Use the no form of this

command to restore the default configuration.

When you filter routes for redistribution by following the route-map rule, the match rule of the

route-map rule is specific for the original redistribution parameters. The route-map rule works only

when the redistributed OSPF routes follow the match rule.

The range of set metric is from 0 to 16777214 for the associated route-map. If the value exceeds

the range, introducing a route fails.

The following are the rules for configuring the no form of the redistribute command:1. If the

form specifies some parameters, restore their default values.2. If the

form contains no

parameter, delete the whole command..

Configuration

Examples

N/A

Related

Commands

Command

Description

summary-address

Configures the aggregate route for the external

route of the OSPF route area.

default-metric

Sets the default metric of the OSPF

redistribution route.

Platform

Description

N/A

2.47 router ospf

Use this command to create the OSPF routing process in global configuration mode. Use the

form

of this command to restore the default setting.

router ospf

no router ospf

process-id

Parameter

Description

Parameter

Description

process-id

ID of an OSPF process. If the process ID is not configured, process 1

is configured.

Defaults

No OSPF routing process exists by default.

Command

Mode

Global configuration mode

Usage Guide

Based on the original implementation, the RGOS10.1 adds the routing process ID to multi-instance

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 741 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: