Ruijie RG-S29 Series Скачать руководство пользователя страница 1349

Страница: 1349 / 1510

Command Reference QoS Commands

no mls qos trust

default mls qos trust

Parameter

Description

Parameter

Description

cos

Specifies the CoS trust mode.

dscp

Specifies the DSCP trust mode.

ip-precedence

Specifies the IP-PRE trust mode.

Defaults

No trust mode is configured by default.

Command

Mode

Interface configuration mode.

Usage Guide

N/A

Configuration

Examples

The following example configures the CoS trust mode.

Ruijie(config)# interface gigabitethernet 1/1

Ruijie(config-if)# mls qos trust cos

Related

Commands

Command

Description

show mls qos interface

interface-id

Displays the specified interface configuration.

Platform

Description

N/A

2.11 police

Use this command to configure traffic policing for a class map in a policy map. Use the

form of this

command to remove traffic policing for the class map.

police

rate-bps

burst-byte

[

exceed-action

{

drop

dscp

new-dscp

cos

new-cos

[

none-tos

] } ]

no police

Parameter

Description

Parameter

Description

rate-bps

Bandwidth limit value per second (The unit is KBits). This value

depends on the specific product.

burst-byte

Burst traffic limit value (The unit is KBytes). This value depends on

the specific product.

drop

Drops the packet. This is available only when the packet exceeds the

bandwidth limit.

dscp

new-dscp

Modifies the DSCP value of the packet. This is available only when

the packet exceeds bandwidth limit. The DSCP value range is from 0

to 63.

cos

new-cos

Modifies the CoS value of the packet. This is available only when the

«
...
1347
1348
1349
1350
1351
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды