Ruijie RG-S29 Series Скачать руководство пользователя страница 1153

Страница: 1153 / 1510

Configuration Guide DHCP Snooping Commands

Defaults

This function is disabled by default.

Command

Mode

Global configuration mode

Usage Guide

This command only works for request packets with Option82.

If strategy is

“keep” or “drop”, trailing padding is not needed for request packets with Option82.

If strategy is

“replace”, trailing padding is needed for request packets with Option82.

Request packets without Option82 are padded with trailing.

Configuration

Examples

The following example sets

“keep” as strategy.

Ruijie# configure terminal

Ruijie(config)# ip dhcp snooping information option strategy keep

Related

Commands

Command

Description

N/A

Platform

Description

N/A

14.10 ip dhcp snooping loose-forward

Use this command to enable DHCP Snooping loose forwarding.

Use the

form of this command to restore the default setting.

ip dhcp snooping loose-forward

no ip dhcp snooping loose-forward

Parameter

Description

Parameter

Description

N/A

Defaults

This function is disabled by default.

Command

Mode

Global configuration mode

Usage Guide

After this feature is enabled, when the capacity of DHCP Snooping binding entries is reached, DHCP

packets of new users are forwarded and obtain addresses, but DHCP Snooping does not record

binding entries of new users.

Configuration

Examples

The following example enables DHCP Snooping loose forwarding.

Ruijie# configure terminal

Ruijie(config)# ip dhcp snooping loose-forward

«
...
1151
1152
1153
1154
1155
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 1153 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: