Ruijie RG-S29 Series Скачать руководство пользователя страница 457

Страница: 457 / 1510

Command Reference ERPS Commands

Enter configuration commands, one per line. End with CNTL/Z.

# Configure the method of monitoring the link state.

Ruijie(config)# erps monitor link-state by oam vlan 100

Related

Commands

Command

Description

N/A

Platform

Description

N/A

13.4 erps raps-vlan

Use this command to configure the R-APS VLAN of Ethernet ring.

erps

raps-vlan

vlan-id

no erps

raps-vlan

vlan-id

Parameter

Description

Parameter

Description

vlan-id

R-APS VLAN ID

Defaults

No R-APS VLAN is configured.

Command

Mode

Global configuration mode.

Usage Guide

The R-APS VLAN must be the VLAN that is not used on the device. Cannot set the VLAN1 to the

R-APS VLAN.

The same Ethernet ring of different devices needs the same R-APS VLAN.

If you want to transparently transmit the ERPS protocol packets on a device without the ERPS

function configured, make sure that only the two ports connected to the Ethernet ring on this device

allow the R-APSA VLAN packets corresponding to this ERPS ring passing through. Otherwise, the

other VLAN packets may enter the R-APS VLAN through the transparent transmission, causing the

shock to the ERPS ring.

Configuration

Examples

# Enter the privileged EXEC mode.

Ruijie# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

#Configure the R-APS VLAN globally.

Ruijie(config)# erps raps-vlan 4093

Related

Command

Description

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды