Ruijie RG-S29 Series Скачать руководство пользователя страница 334

Страница: 334 / 1510

Command Reference Private VLAN Commands

command to restore the default setting.

private-vlan

{

community

isolated

primary

}

no private-vlan

{

community

isolated

primary

}

default private-vlan

{

community

isolated

primary

}

Parameter

Description

Parameter

Description

community

Sets the community VLAN.

isolated

Sets the isolated VLAN.

primary

Sets the primary VLAN.

Defaults

No private VLAN feature is configured by default.

Command

mode

VLAN configuration mode

Usage Guide

N/A

Configuration

Examples

The following example configures the private VLAN feature.

Ruijie(config)#vlan 90

Ruijie(config-vlan)#private-vlan primary

Ruijie(config-vlan)#vlan 91

Ruijie(config-vlan)#private-vlan isolated

Ruijie(config-vlan)#vlan 92

Ruijie(config-vlan)#private-vlan community

The following example disables the private VLAN feature using the

no private-vlan

command.

Ruijie(config)#vlan 90

Ruijie(config-vlan)#no private-vlan primary

Ruijie(config-vlan)#vlan 91

Ruijie(config-vlan)#no private-vlan isolated

Ruijie(config-vlan)#vlan 92

Ruijie(config-vlan)#no private-vlan community

The following example disables the private VLAN feature using the

default private-vlan

command.

Ruijie(config)#vlan 90

Ruijie(config-vlan)#default private-vlan primary

Ruijie(config-vlan)#vlan 91

Ruijie(config-vlan)#default private-vlan isolated

Ruijie(config-vlan)#vlan 92

Ruijie(config-vlan)#default private-vlan community

Related

Commands

Command

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 334 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: