Ruijie RG-S29 Series Скачать руководство пользователя страница 789

Страница: 789 / 1510

Command Reference

OSPFv3 Commands

enable mib-binding

no enable mib-binding

Parameter

Description

Parameter

Description

N/A

Defaults

MIB is bound to an OSPFv3 process with the smallest process number by default.

Command

Mode

Routing process configuration mode

Usage Guide

OSFPv3 MIB has no configuration information about OSFPv3 processes. You can operate only one

OSFPv3 process through SNMP. OSFPv3 MIB is bound to the OSFPv3 process with the smallest

process number by default. Users' operations take effect on this process.

To operate a specific OSFPv3 process through SNMP, you can bind OSFPv3 MIB to the process.

Configuration

Examples

The following example enables users to operate the OSPFv3 process with the process number of 100

through SNMP.

Ruijie(config)# ipv6 router ospf 100

Ruijie(config-router)# enable mib-binding

Related

Commands

Command

Description

show ipv6 ospf

Displays global OSPFv3 configuration

information.

enable traps

Enables the OSPFv3 trap function.

Platform

Description

N/A

3.15 enable traps

OSPFv3 processes support eight types of trap information, which are classified into two categories.

Use this command to send specific trap information. Use the

form of this command to restore the

default setting.

enable traps

[

error

[

IfConfigError | IfRxBadPacket | VirtIfConfigError | VirtIfRxBadPacket

] |

state-change

[

IfStateChange | NbrStateChange | NssaTranslatorStatusChange |

VirtIfStateChange | VirtNbrStateChange

] ]

no enable traps

[

error

[

IfConfigError | IfRxBadPacket | VirtIfConfigError | VirtIfRxBadPacket

] |

state-change

[

IfStateChange | NbrStateChange | NssaTranslatorStatusChange |

VirtIfStateChange | VirtNbrStateChange

] ]

Parameter

Description

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 789 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: