Ruijie RG-S29 Series Скачать руководство пользователя страница 667

Страница: 667 / 1510

Command Reference

RIP Commands

Ruijie(config)#interface fastEthernet 0/1

Ruijie(config-if-FastEthernet 0/1)# ip rip authentication text-password hello

Related

Commands

Command

Description

ip rip authentication mode

Defines the RIP authentication mode.

ip rip authentication key-chain

Enables the RIP authentication mode and

specifies the keychain used for RIP

authentication. Only RIPv2 supports

authentication.

Platform

Description

N/A

1.12 ip rip default-information

Use this command to advertise the default route through a RIP interface. Use the

form of this

command to restore the default setting.

ip rip default-information

{

only

originate

}

[

metric

metric-value

]

no ip rip default-information

Parameter

Description

Parameter

Description

only

Notifies the default route rather than other routes.

originate

Notifies the default route and other routes.

metric

metric-value

Specifies the metric value of the default route, in the range from1 to

15.

Defaults

No default route is configured by default. The default metric value is 1.

Command

Mode

Interface configuration mode

Usage Guide

After you configure this command on a specified interface, a default route is generated and notified

through the interface. If the

ip rip default-information

command of the interface and the

default-information originate

command of the RIP process are configured at the same time, only

the default route of the interface is advertised.

RIP will no longer learn the default route notified by the neighbor if any interface is configured with the

ip rip default-information command.

Configuration

Examples

The following example creates a default route which is notified on ethernet0/1 only.

Ruijie(config)#interface ethernet 0/1

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды