Ruijie RG-S29 Series Скачать руководство пользователя страница 321

Страница: 321 / 1510

Command Reference VLAN Commands

remove

Removes the trunk/uplink port from the VLAN port.

except

Removes the trunk/uplink port from the VLAN and adds the port to all

the other VLANs.

only

Adds the trunk/uplink port to the specified VLAN and removes the

port from the VLANs not on the VLAN list.

vlan-list

Specifies the VLAN.

Defaults

The trunk/unlink port is in all VLANs by default.

Command

mode

Interface configuration mode.

Usage Guide

A trunk/uplink port transmits all VLAN (1-4094) data by default. You can block some VLAN data by

configuring

this command. Use the

show interfaces

command to display configuration.

Configuration

Examples

The following example removes trunk port GigabitEthernet 0/10 from VLAN 2.

Ruijie(config)# interface gigabitEthernet 0/10

Ruijie(config-if-GigabitEthernet 0/10)# switchport mode trunk

Ruijie(config-if-GigabitEthernet 0/10)# switchport trunk allowed vlan remove

The following example removes trunk port GigabitEthernet 0/10 from VLAN 2.

Ruijie(config)# interface gigabitEthernet 0/10

Ruijie(config-if-GigabitEthernet 0/10)# switchport trunk allowed vlan except

The following example removes uplink port GigabitEthernet 0/10 from VLAN 10.

Ruijie(config)# interface gigabitEthernet 0/10

Ruijie(config-if-GigabitEthernet 0/10)# switchport mode uplink

Ruijie(config-if-GigabitEthernet 0/10)# switchport trunk allowed vlan remove

The following example adds uplink port GigabitEthernet 0/10 to all VLANs except VLAN10.

Ruijie(config)# interface gigabitEthernet 0/10

Ruijie(config-if-GigabitEthernet 0/10)# switchport trunk allowed
vlan except 10

Related

Commands

Command

Description

N/A

Platform

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды