Ruijie RG-S29 Series Скачать руководство пользователя страница 1453

Страница: 1453 / 1510

Command Reference SNMP Commands

Description

1.7 snmp-server enable traps

Use this command to enable the SNMP agent to send the SNMP trap massage to NMS. Use the

form of this command to disable the SNMP agent to send the SNMP trap massage to NMS.

snmp-server enable traps

[

notification-type

]

no snmp-server enable traps

Parameter

Description

Parameter

Description

notification-type

Specifies the type of trap messages.

snmp: SNMP trap message

bridge: Bridge trap message.

mac-notification: MAC trap message.

ospf: OSPF trap message.

vrrp: VRRP trap message.

web-auth: Web authentication trap message.

Defaults

Sending trap message to the NMS is disabled by default.

Command

mode

Global configuration mode.

Usage Guide

This command must be used together with the

snmp-server host

command to

send the trap

message. Specifying no trap type indicates all trap messages are sent.

Configuration

Examples

The following example enables the SNMP agent to send the SNMP trap message.

Ruijie(config)# snmp-server enable traps snmp

Ruijie(config)# snmp-server host

192.168.12.219

public snmp

Related

Commands

Command

Description

snmp-server host

Specifies the SNMP host to send the SNMP

trap message.

Platform

Description

N/A

1.8 snmp-server flow-control

Use this command to configure the SNMP flow control.

Use the

form of this command to restore

the default setting.

«
...
1451
1452
1453
1454
1455
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды