Ruijie RG-S29 Series Скачать руководство пользователя страница 410

Страница: 410 / 1510

Command Reference LLDP Commands

Defaults

The default is

txrx

Command

Mode

Interface configuration mode

Usage Guide

Disable LLDP operating mode on the interface. The interface won't send and receive LLDP packets.

The precondition for enabling LLDP on the interface is that LLDP has been enabled globally and

LLDP operates in tx, rx or txrx mode.

Configuration

Examples

The following example sets LLDP operating mode to tx on the interface.

Ruijie#config

Ruijie(config)#interface gigabitethernet 0/1

Ruijie(config-if)#lldp mode tx

Related

Commands

Command

Description

show lldp status

Displays LLDP status information

Platform

Description

N/A

11.16 lldp network-policy profile

Use this command to create an LLDP network policy and enter the LLDP network policy configuration

mode. Use the no form of this command to delete the policy.

lldp network-policy profile

profile-num

no lldp network-policy profile

profile-num

Parameter

Description

Parameter

Description

profile-num

ID of an LLDP network policy, in the range from 1 to 1024.

Defaults

N/A

Command

Mode

Global configuration mode

Usage Guide

This command is used to enter the LLDP network policy configuration mode. When this command is

run, the policy ID must be specified.

In LLDP network-policy mode, the {

voice

voice-signaling

}

vlan

command can be used to

configure the specific network policy.

Configuration

Examples

The following example creates an LLDP network policy whose ID is 1.

Ruijie#config

Ruijie(config)#lldp network-policy profile 1

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды