Ruijie RG-S29 Series Скачать руководство пользователя страница 511

Страница: 511 / 1510

Command Reference

IPv6 Commands

A general prefix could contain multiple prefixes.

These longer specified prefixes are usually used for the Ipv6 address configuration on the interface.

Configuration

Examples

The following example configures manually a general prefix as my-prefix.

Ruijie(config)# ipv6 general-prefix my-prefix 2001:1111:2222::/48

Related

Commands

Command

Description

ipv6 address prefix-name

sub-bits/prefix-length

Configures the interface address using the general prefix.

show ipv6 general-prefix

Displays the general prefix.

Platform

Description

N/A

3.6 ipv6 hop-limit

Use this command to configure the default hopcount to send unicast messages in the global

configuration mode.

ipv6 hop-limit

value

no ipv6 hop-limit

Parameter

Description

Parameter

Description

N/A

Defaults

The default is 64.

Command Mode

Global configuration mode.

Usage Guide

This command takes effect for the unicast messages only, not for multicast messages.

Configuration

Examples

Ruijie(config)#

ipv6 hop-limit

100

Related

Commands

Command

Description

N/A

Platform

Description

N/A

3.7 ipv6 icmp error-interval

Use this command to set the frequency with which ICMPv6-oversize error packets are sent. Use the

form of this command to restore the default setting.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды