Ruijie RG-S29 Series Скачать руководство пользователя страница 921

Страница: 921 / 1510

Command Reference

IGMP Snooping Commands

Description

profile-number

Profile number, in the range from 1 to 1024

Defaults

No profile is created by default.

Command

Mode

Global configuration mode

Usage Guide

The profile is a filter to permit/deny specified groups in the following steps:



Use the

ip igmp profile

command to create a profile and enter profile configuration mode.



Use the

range

command to define a profile range.



Use the

permit

command to permit this profile in the filtering, or use the

deny

command to deny

this profile in the filtering.



If the

deny

command is used without any profile specified, all profiles in the profile are permitted.



If the

permit

command is used without any profile specified, all profiles in the profile are denied.

Configuration

Examples

The following example creates and permits profile 1 with addresses from 224.2.2.2 to 224.2.2.244.

Ruijie(config)# ip igmp profile 1

Ruijie(config-profile)# range 224.2.2.2 224.2.2.244

Ruijie(config-profile)# permit

Platform

Description

N/A

2.5 ip igmp snooping

Use this command to enable IGMP snooping and enter the IVGL mode.

ip igmp snooping ivgl

Use this command to enable IGMP snooping and enter the SVGL mode.

ip igmp snooping svgl

Use this command to enable IGMP snooping and enter the IVGL-SVGL mode.

ip igmp snooping ivgl-svgl

Use the

default

command to restore the default setting.

no ip igmp snooping

default ip igmp snooping

Parameter

Description

Parameter

Description

N/A

Defaults

IGMP Snooping is disabled by default.

Command

Global configuration mode

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды