Ruijie RG-S29 Series Скачать руководство пользователя страница 1377

Страница: 1377 / 1510

Command Reference REUP Commands

1.5 mac-address-table move update receive vlan

Use this command to configure the VLANs processing MAC address update packets.

mac-address-table move update receive vlan

vlan-range

no mac-address-table move update receive vlan

vlan-range

Parameter

Description

Parameter

Description

vlan-range

Range of the VLANs processing MAC address update packets.

Defaults

All VLANs process MAC address update packets.

Command

Mode

Global configuration mode.

Usage Guide

This command can be used to disable some VLANs from processing MAC address update packets.

VLANs disabled from processing MAC address update packets can still recover downlink data

transmission of the uplink device using MAC address update packets, but the capability to provide

convergence on link failure will be degraded.

Configuration

Examples

The following example configures VLANs processing MAC address update packets:

Ruijie(config)# no mac-address-table move update receive vlan 20

Related

Commands

Command

Description

mac-address-table move update receive

Enables REUP to receive MAC address update

packets.

Platform

Description

N/A.

1.6 mac-address-table move update transit

Use this command to enable REUP to transmit the mac-address-table update messages.

mac-address-table move update transit

no mac-address-table move update transit

Parameter

Description

Parameter

Description

N/A.

Defaults

Disabled.

«
...
1375
1376
1377
1378
1379
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды