Ruijie RG-S29 Series Скачать руководство пользователя страница 1187

Страница: 1187 / 1510

Configuration Guide IP Source Guard Commands

18 IP Source Guard Commands

18.1 ip source binding

Use this command to add static user information to IP source address binding database.

Use the

form of this command to delete static user information from IP source address binding

database.

ip source binding

mac-address

{ vlan

vlan-id

}

ip-address

{

interface

interface-id

| ip-mac |

ip-only

}

ip source binding

mac-address

{ vlan

vlan-id

}

ip-address

{

interface

interface-id

| ip-mac |

ip-only

}

Parameter

Description

Parameter

Description

mac-address

Adds user MAC address statically.

vlan-id

Adds user VLAN ID statically.

ip-address

Adds user IP address statically.

interface-id

Adds user interface ID statically.

ip-mac

The global binding type is IP+MAC

ip-only

The global binding type is IP only.

Defaults

No static address is added by default.

Command

Mode

Global configuration mode

Usage Guide

This command allows specific clients to go through IP source guard detection instead of DHCP.

This command is supported on the wired L2 switching port, AP port and sub interface.

This command enables global binding for IP source guard so that specific clients will get detected on

all interfaces.

A static IPv6 source binding is valid either on wired and WLAN interfaces or in global

configuration mode.

A new binding will overwrite the old one sharing the same configuration.

Configuration

Examples

The following example adds the interface Id of static users.

Ruijie# configure terminal

Ruijie(config)# ip source binding 0000.0000.0001 vlan 1 1.1.1.1 interface

GigabitEthernet 0/1

Ruijie(config)# end

The following example adds static user information based on IP-MAC binding.

«
...
1185
1186
1187
1188
1189
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды