Ruijie RG-S29 Series Скачать руководство пользователя страница 723

Страница: 723 / 1510

Command Reference

OSPFv2 Commands

Description

2.29 ip ospf hello-interval

Use this command to set the interval for sending Hello packets in interface configuration mode. Use

the

form of this command to restore the default setting.

ip ospf hello-interval

seconds

no ip ospf hello-interval

Parameter

Description

Parameter

Description

seconds

Interval for sending Hello packets in seconds. The range is from1 to

65535.

Defaults

The defaults are as follows:

10secons for Ethernet

10seconsfor PPP or HDLC encapsulated interfaces

10secons for frame relay PTP interfaces

30secons for non-frame relay PTP sub-interface and X.25 interfaces

Command

Mode

Interface configuration mode

Usage Guide

The interval of sending the Hello packets is included in the Hello packet. A shorter interval means that

OSPF detects the topological change faster, which will increase network traffic. The Hello packet

sending intervals for all the devices in the same network segment must be the same. To manually

modify the interval to determine neighbor death, ensure that the Hello packet sending interval cannot

be greater than dead-interval of the neighbor.

Configuration

Examples

The following example configures the interval of sending the Hello packets on fastEthernet 0/1 to15.

Ruijie(config)# interface fastEthernet 0/1

Ruijie(config-if-FastEthernet 0/1)# ip address

172.16.10.1 255.255.255.0

Ruijie(config-if-FastEthernet 0/1)# ip ospf hello-interval

Related

Commands

Command

Description

ip ospf dead-interval

Sets the interval for determining the death of

the OSPF neighbor.

Platform

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды