Ruijie RG-S29 Series Скачать руководство пользователя страница 934

Страница: 934 / 1510

Command Reference

IGMP Snooping Commands

This command lets you adjust the waiting time after receiving the query message. This command takes

effect only after the switch receives the next member join message. This command does not change the

current wait time.

Configuration

Examples

The following examples sets the aging time of the routing interface that the switch learns dynamically to

100 seconds.

Ruijie(config)# ip igmp snooping query-max-response-time

100

Platform

Description

N/A

2.22 ip igmp snooping suppression enable

Use this command to enable IGMP snooping suppression.

Use the

default

form of this command to restore the default setting.

ip igmp snooping suppression enable

no ip igmp snooping suppression enable

default ip igmp snooping suppression enable

Parameter

Description

Parameter

Description

N/A

Defaults

This function is disabled by default.

Command

Mode

Global configuration mode

Usage Guide

When this function is enabled, IGMP Snooping only forwards the first report from a specific VLAN or

group, and suppresses the following reports to constrain traffic in the networks.

This function is only supported on IGMPv1 and IGMPv2 reports.

Configuration

Examples

The following example enables IGMP snooping suppression on the device.

Ruijie(config)# ip igmp snooping suppression enable

Platform

Description

N/A

2.23 ip igmp snooping svgl profile

Use this command to specify the multicast group address range applied in the SVGL/IVGL-SVGL mode.

Use the

default

form of this command to restore the default setting.

ip igmp snooping svgl profile

profile-number

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды