Ruijie RG-S29 Series Скачать руководство пользователя страница 892

Страница: 892 / 1510

Command Reference

Protocol-independent Configuration Commands

6.27 send-lifetime

Use this command in the encryption key configuration mode to specify the lifetime of an encryption key

in its send direction. Use the no form of this command to restore the default value.

send-lifetime

start-time

{

infinite

end-time

duration

seconds

}

no send-lifetime

Parameter

description

Parameter

Description

start-time

Start time of the lifetime.

infinite

Indicates that the encryption key is valid for ever.

end-time

End time of the encryption key. It must be later than the start time.

duration

seconds

Duration of the encryption key after the start time. The value ranges from 1 to

2147483646.

Default

infinite

Command

mode

Encryption key configuration mode

Usage

guideline

Use this command to specify the lifetime of an encryption key in its send direction.

Examples

The following example configures the lifetime from 0:00 on September 9, 2000 to 0:00 on October 12,

2011

Ruijie(config)# key chain ripkeys

Ruijie(config-keychain)# key 1

Ruijie(config-keychain-key)# send-lifetime 00:00:00 Sep 9 2000 00:00:00 Dec 12

2011

Related

command

Command

Description

Platform

description

6.28 set ip default next-hop

Use this command to specify the default next-hop IP address for the packets that match the rule in the

route map configuration mode. Use the

form of this command to remove the setting.

set ip default next-hop

ip-address

[

weight

] [

…ip-address

[

weight

] ]

no set ip default next-hop

[

ip-address

[

weight

] [

…ip-address

[

weight

] ] ]

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды