Ruijie RG-S29 Series Скачать руководство пользователя страница 47

Страница: 47 / 1510

Command Reference

Basic Configuration Management Commands

2.46 show this

Use this command to display effective configuration in the current mode.

show this

Parameter

Description

Parameter

Description

N/A

Defaults

N/A

Command

Mode

All modes.

Usage Guide

The configuration in the following range modes cannot be displayed. If the

show this

command is

run, the outcome is NULL.

1. Use the

line

first-line

last-line

command to configure lines in a continuous group and enter LINE

configuration mode.

2. Use the

vlan range

command to configure VLANs and enter vlan range configuration mode.

3. Use the

interface range

command to configure interfaces and enter interface range

configuration mode.

vlan range

interface range

mode, if the number of VLANs or interfaces exceeds 50, the

configuration of the first 50 VLANs or interfaces will be displayed.

Configuration

Examples

Use this command to display effective configuration on interface fastEthernet 0/1.

Ruijie (config)#interface fastEthernet 0/1

Ruijie (config-if-FastEthernet 0/1)#show this

Building configuration...

spanning-tree link-type point-to-point

spanning-tree mst 0 port-priority 0

end

Ruijie (config-if-FastEthernet 0/1)#

Use this command to display configuration on interface VLAN 1-3.

Ruijie(config-if-range)#show this

Building configuration...

interface VLAN 1

ip address dhcp

interface VLAN 2

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды