Ruijie RG-S29 Series Скачать руководство пользователя страница 451

Страница: 451 / 1510

Command Reference QinQ Commands

12.27 traffic-redirect access-group acl nested-vlan

vid

Use this command to configure vid add policy list based on flow on dot1q-tunne port. Use the

default

form of this command to restore the default setting.

traffic-redirect access-group

acl

nested-vlan

vid

no traffic-redirect access-group

acl

nested

–vlan

default traffic-redirect access-group

acl

nested -vlan

Parameter

Description

Parameter

Description

acl

Flow matching.

vid

vid list to be added.

Defaults

The policy list is null by default.

Command

Mode

Interface configuration mode.

Usage Guide

N/A

Configuration

Examples

The following example specifies the vid of input message whose source address is 1.1.1.3 as 9.

Ruijie#configure

Ruijie(config)#ip access-list standard 20

Ruijie(config-std-nacl)#permit host 1.1.1.3

Ruijie(config-std-nacl)#exit

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if)# switchport mode dot1q-tunnel

Ruijie(config-if)# traffic-redirect access-group 20 nested-vlan 10 in

Ruijie(config-if)# end

Related

Commands

Command

Description

show traffic-redirect

N/A

Platform

Description

N/A

12.28 traffic-redirect access-group acl outer-vlan

vid

Use this command to configure the modify policy list of outer vid based on flow on access, trunk,

hybrid port. Use the

default

form of this command to restore the default setting.

traffic-redirect access-group

acl

outer-vlan

vid

no traffic-redirect access-group

acl

outer-vlan

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 451 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: