Ruijie RG-S29 Series Скачать руководство пользователя страница 405

Страница: 405 / 1510

Command Reference LLDP Commands

Mode

Usage Guide

To guarantee the normal communication between local device and neighbor device, the same

LLDP packet encapsulation format must be used.

Configuration

Examples

The following example sets LLDP packet encapsulation format to

SNAP.Ruijie#config

Ruijie(config)#interface gigabitethernet 0/1

Ruijie(config-if)#lldp encapsulation snap

Related

Commands

Command

Description

show lldp status

Displays LLDP status information.

Platform

Description

N/A

11.9 lldp error-detect

Use this command to configure the LLDP error detection, including the detection of VLAN

configurations on both sides of the link, port state detection, port aggregation configuration detection,

MTU configuration detection and loop detection. If any error is detected by LLDP, warning message

will be printed to notify the administrator. Use the

form of this command to disable this function.

lldp error-detect

no lldp error-detect

Parameter

Description

Parameter

Description

N/A

Defaults

This function is enabled by default.

Command

Mode

Interface configuration mode.

Usage Guide

LLDP error detection relies on the specific TLV in the LLDP packets exchanged between devices on

both sides of the link. To ensure normal functioning of the detection feature, correct TLVs must be

advertised.

Configuration

Examples

The following example configures LLDP error detection.

Ruijie#config

Ruijie(config)#interface gigabitethernet 0/1

Ruijie(config-if)#lldp error-detect

Related

Command

Description

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды