Ruijie RG-S29 Series Скачать руководство пользователя страница 368

Страница: 368 / 1510

Command Reference MSTP Commands

Platform

Description

N/A

9.20 spanning-tree bpduguard

Use this command to enable the BPDU guard function on the interface. You can use the

enabled

disabled

option of the command to enable or disable the BPDU guard function on the interface.

spanning-tree bpduguard

[

enabled

disabled

]

Parameter

Description

Parameter

Description

enabled

Enables BPDU guard on the interface.

disabled

Disables BPDU guard on the interface.

Defaults

This function is disabled by default.

Command

Mode

Interface configuration mode.

Usage Guide

1. If BPDU guard is enabled on a port, the port enters the error-disabled state after receiving a

BPDU.

2. Run command

errdisable recovery

[

interval

seconds

] to recover the interface in

Error-disabled state.

Configuration

Examples

The following example enables the BPDU guard function on the interface.

Ruijie(config)# interface gigabitethernet 1/1

Ruijie(config-if-interface-id-interface-id)# spanning-tree bpduguard enable

Related

Commands

Command

Description

show spanning-tree interface

Displays the STP configuration of the interface.

Platform

Description

N/A

9.21 spanning-tree compatible enable

Use this command to send the message selectively carried with MSTI according to the interface

attribute of current port to realize interconnection with other vendors. Use the

form of this

command to restore the default setting.

spanning-tree compatible enable

no spanning-tree compatible enable

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды