Ruijie RG-S29 Series Скачать руководство пользователя страница 208

Страница: 208 / 1510

Command Reference

CA-MONITOR Commands

Usage Guide

Use the command to display the current temperature and threshold configuration of each board.

The temperature threshold of CA products involves the alarm threshold and the hazard threshold.

Alarm threshold: When the temperature of the board exceeds the alarm threshold, the active supervisor

module generates a Syslog message and the Alarm LED on the panel becomes yellow.

Hazard threshold: It indicates the power-off temperature. When the temperature of the board exceeds

the hazard threshold, the board powers off automatically. In addition, the active supervisor module

generates a Syslog message and the Alarm LED on the panel becomes red.

Configuration

Examples

The following example displays the temperature and threshold configuration of all boards of S29XS.

Ruijie#show temperature

Slot Card_type Current(C) Status

------- -------------------------------- ---------- ---------

1/0 S2910-48GT4XS-E 43 ok

S2910-48GT4XS-E 42 ok

Ruijie#

The following example displays the temperature and threshold configuration of all boards of S29XS

PoE.

Ruijie#show temperature

slot_type Current(C) Status

------- -------------------------------- ---------- ---------

0 S2910C-24GT2XS-HP-E 28 ok

Ruijie#

Prompt

Messages

N/A

Platforms

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды