Ruijie RG-S29 Series Скачать руководство пользователя страница 492

Страница: 492 / 1510

Command Reference

ARP Commands

2.7 arp timeout

Use this command to configure the timeout for the ARP static mapping record in the ARP cache.

Use the

form of this command to restore the default setting.

arp timeout

seconds

no arp timeout

Parameter

Description

Parameter

Description

secondsv

The timeout is in the range from 0 to 2147483 in the unit of seconds.

Defaults

The default is 3600.

Command

Mode

Interface configuration mode/Global configuration mode

Usage Guide

The ARP timeout setting is only applicable to the IP address and the MAC address mapping that

are learned dynamically. The shorter the timeout, the truer the mapping table saved in the ARP

cache, but the more network bandwidth occupied by the ARP. Hence the advantages and

disadvantages should be weighted. Generally it is not necessary to configure the ARP timeout

unless there is a special requirement.

Configuration

Examples

The following example sets the timeout for the dynamic ARP mapping record that is learned

dynamically from FastEthernet port 0/1 to 120 seconds.

Ruijie(config)# interface fastEthernet

0/1

Ruijie(config-if)# arp timeout

120

Related

Commands

Command

Description

clear arp-cache

Clears the ARP cache list.

show interface

Displays the interface information.

Platform

Description

N/A

2.8 arp trusted

Use this command to set the maximum number of trusted ARP entries. Use the

form of this

command to restore the default setting.

arp trusted

number

no arp

trusted

Parameter

Description

Parameter

Description

number

Maximum number of trusted ARP entries.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды