Ruijie RG-S29 Series Скачать руководство пользователя страница 1413

Страница: 1413 / 1510

Command Reference VRRP Commands

If the host IP address is link-local, an interface must be specified.

If a VRRP router owns the IP address of the physical interface, the priority is 255. Keep the

priority when the monitored IP address or interface is set.

Configuration

Examples

The following example enables the VRRP group 1 to monitor the routed port Fa1/1. If the Fa1/1 link is

disconnected, the priority of the VRRP group decreases by 30. When the Fa1/1 link recovers, the

priority of VRRP group 1 is restored.

Ruijie#configure terminal

Ruijie(config)#interface GigabitEthernet 0/0

Ruijie(config-if-GigabitEthernet 0/0)#no switchport //used on the switch.

Ruijie(config-if-GigabitEthernet 0/0)#ip address 10.0.1.1 255.255.255.0

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 ip 10.0.1.20

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 priority 254

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 track GigabitEthernet 1/1 30

Related

Commands

Command

Description

vrrp

group

ipaddress

[

secondary

]

Enables the VRRP function and set the IP

address for the virtual device.

vrrp

group

priority

level

Sets the VRRP group priority.

Platform

Description

N/A

4.15 vrrp version

Use this command to configure the version of sending the IPv4 VRRP multicast packets.

For the IPv4 VRRP, there are two versions: VRRPv2 and VRRPv3.

Use the

form of this command to restore the default setting.

vrrp

group

version

{

}

no vrrp

group

version

Parameter

Description

Parameter

Description

Uses the VRRPv2 version to send the packets.

Uses the VRRPv3 version to send the packets.

Defaults

The default is VRRPv2.

Command

Mode

Interface configuration mode

Usage Guide

Considering the compatibility of VRRPv2 and VRRPv3 for the IPv4 VRRP, you can choose the

«
...
1411
1412
1413
1414
1415
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды