Ruijie RG-S29 Series Скачать руководство пользователя страница 267

Страница: 267 / 1510

Command Reference Interface Commands

Gi0/18 Yes Enable Enable Enable None

Gi0/19 Yes Enable Enable Enable None

Gi0/20 Yes Enable Enable Enable None

Gi0/21 Yes Enable Enable Enable None

Gi0/22 Yes Enable Enable Enable None

Gi0/23 Yes Enable Enable Enable None

Gi0/24 Yes Enable Enable Enable None

Gi0/25 No - - - -

Gi0/26 No - - - -

Gi0/27 No - - - -

Gi0/28 No - - - -

Related

Commands

Command

Description

N/A

Platform

Description

N/A

1.22 show interfaces

Use this command to display the interface information and optical module information.

show interfaces

[

interface-type interface-number

] [

description | switchport

| trunk

]

Parameter

Description

Parameter

Description

interface-id

interface-number

Interface (including Ethernet interface, aggregate port, SVI or loopback

interface).

description

The description of the interface, including the link status.

switchport

Layer 2 interface information.

trunk

Trunk port, applicable for physical port and aggregate port.

Defaults

Command

Mode

Privileged EXEC mode.

Usage Guide

This command is used to show all basic information if no parameter is specified.

Configuration

Examples

The following example displays the interface information when the Gi0/1 is a Trunk port.

SwitchA#show interfaces gigabitEthernet 0/1

Index(dec):1 (hex):1

GigabitEthernet 0/1 is DOWN , line protocol is DOWN

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды