Ruijie RG-S29 Series Скачать руководство пользователя страница 198

Страница: 198 / 1510

Command Reference

CWMP Commands

Description

9.7 cpe url

Use this command to configure the URL of the CPE to which the ACS will connect.

Use the

form of this command to restore default setting.

cpe url

url

no cpe url

Parameter

Description

Parameter

Description

url

Specifies the URL of the CPE.

Defaults

N/A

Command

Mode

CWMP configuration mode

Usage Guide

Use this command to configure the URL of the CPE to which the ACS will connect. If no CPE URL is

manually specified but a dynamic CPE URL is obtained through DHCP, the ACS initiates a

connection to the CPE using the dynamically obtained CPE URL. The URL of the CPE should meet

the following format requirements:



The URL of the CPE is formatted as http://ip [: port ]/ path.



The URL of the CPE consists of at most 256 characters.

Configuration

Examples

The following example specifies the URL of the CPE to

http://10.10.10.1:7547/acs

Ruijie#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Ruijie(config)#cwmp

Ruijie(config-cwmp)#cpe url

http://10.10.10.1:7547/

Ruijie(config-cwmp)#

Related

Commands

Command

Description

show cwmp configuration

Displays the current configuration of CWMP.

show cwmp status

Displays the running status of CWMP.

Platform

Description

N/A

9.8 cpe username

Use this command to configure the ACS username to be authenticated for the CPE to connect to the

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды