Ruijie RG-S29 Series Скачать руководство пользователя страница 197

Страница: 197 / 1510

Command Reference

CWMP Commands

cpe password

{

password

encryption-type encrypted-password

}

no cpe password

Parameter

Description

Parameter

Description

password

Configures the CPE user password to be authenticated for the ACS

to connect to the CPE.

encryption-type

Specifies the encryption type, which can be set to 0 (indicating that

no encryption is used) or 7 (indicating that simple encryption is

used).

encrypted-password

Specifies the password in encrypted form.

Defaults

encryption-type: 0

encrypted-password: N/A

Command

Mode

CWMP configuration mode

Usage Guide

Use this command to configure the CPE user password to be authenticated for the ACS to connect

to the CPE. In general, the encryption type does not need to be specified. The encryption type needs

to be specified only when copying and pasting the encrypted password of this command. A valid

password should meet the following format requirements:

The command contains English letters in upper or lower case and numeric characters.

Blanks are allowed at the beginning of the password but will be ignored. Intermediate and

ending blanks, however, are regarded as a part of the password.

Configuration

Examples

The following example configures the CPE password to be authenticated for the ACS to connect to

the CPE to 123.

Ruijie#config terminal

Enter configuration commands, one per line. End with CNTL/Z.

Ruijie(config)#cwmp

Ruijie(config-cwmp)#cpe password 123

Ruijie(config-cwmp)#

Related

Commands

Command

Description

show cwmp configuration

Displays the current configuration of CWMP.

show cwmp status

Displays the running status of CWMP.

acs username

Configures the CPE username to be

authenticated for the ACS to connect to the

CPE.

Platform

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды