Ruijie RG-S29 Series Скачать руководство пользователя страница 692

Страница: 692 / 1510

Command Reference

OSPFv2 Commands

2 OSPFv2 Commands

2.1 area

Use this command to configure the specified OSPF area. Use the

form of this command to restore

the default setting.

area

area-id

no area

area-id

Parameter

Description

Parameter

Description

area-id

ID of the OSPF area. The value can be a decimal integer or an IP

address.

Defaults

No OSPF area is configured by default.

Command

Mode

Routing process configuration mode

Usage Guide

Use the no form of this command to remove the specified OSPF area and its configuration, including

the area-based

area authentication, area default-cost, area filter-list, and area nssa

commands.



Do not remove the OSPF area configuration under the following conditions:



Virtual links exist in the backbone area. The virtual links must be removed at first.



The corresponding network area command exists in any area. All network segment commands

added to an area must be removed at first.

Configuration

Examples

The following example removes the configuration of OSPF area 2.

Ruijie(config)# router ospf 2

Ruijie(config-router)# no area 2

Related

Commands

Command

Description

network area

Defines the interface where OSPF runs and the

belonging area of the interface.

Platform

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды