Ruijie RG-S29 Series Скачать руководство пользователя страница 313

Страница: 313 / 1510

Command Reference VLAN Commands

4 VLAN Commands

4.1 add

Use this command to add one or a group Access interface into current VLAN. Use the

default

form of the command to remove the Access interface.

add interface

{

interface-id

range

interface-range

}

no add interface

{

interface-id

range

interface-range

}

default add interface

{

interface-id

range

interface-range

}

Parameter

Description

Parameter

Description

interface-id

Layer-2 Ethernet interface or layer-2 AP port.

range

interface-range

Range of the Layer-2 Ethernet interface or layer-2 AP port.

Defaults

All layer-2 Ethernet interfaces are in the VLAN1.

Command

mode

VLAN configuration mode.

Usage Guide

This command is only valid for the access port.

The configuration of this command is the same as specifying the VLAN to which interface belongs in

the interface configuration mode (that is the

switchport access vlan

vlan-id

command). For the two

commands of adding the interface to the VLAN, the command configured later will overwrite the one

configured before and take effect.

The configuration of adding the layer-2 AP into current VLAN through this command will only take

effect for the layer-2 AP port, but not for the member port of the layer-2 AP port.

Configuration

Examples

The following example adds the interface GigabitEthernet 0/10 to VLAN20.

Ruijie# configure terminal

SwitchA(config)#vlan 20

SwitchA(config-vlan)#add interface GigabitEthernet 0/10

Ruijie# show interface GigabitEthernet 0/10 switchport

Interface Switchport Mode Access Native Protected VLAN lists

---------- -------- ----- ----- ---- ---------- -------

GigabitEthernet 0/10 enabled ACCESS 20 1 Disabled ALL

The following example adds the interface range GigabitEthernet 0/1-10 to VLAN200.

Ruijie# configure terminal

SwitchA(config)#vlan 200

SwitchA(config-vlan)#add interface range GigabitEthernet 0/1-10

Ruijie# show vlan

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 313 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: