Ruijie RG-S29 Series Скачать руководство пользователя страница 1384

Страница: 1384 / 1510

Command Reference REUP Commands

Platform

Description

N/A.

1.14 switchport backup interface preemption

Use this command to configure the REUP link preemption function.

switchport backup interface

interface-id

preemption mode

{

forced

bandwidth

off

}

switchport backup interface

interface-id

preemption delay

no switchport backup interface

interface-id

preemption delay

Parameter

Description

Parameter

Description

interface-id

The interface id of the backup link.

delay-time

The preemption delay time.

Defaults

The default preemption delay time is 35s.

Command

Mode

Interface configuration mode.

Usage Guide

The preemption mode includes

forced, bandwidth and off

. In the

bandwidth

preemption mode, the

interface with high bandwidth has priority over other interfaces to transmit the data. In the

forced

preemption mode, the primary has priority over backup interfaces to transmit the data. No preemption

event occurs in the

off

preemption mode. By default, the preemption mode is off.

The preemption delay refers to the delay time of the link switchover after the restoration of the link

failure.

Configuration

Examples

The following example shows how to set the dual link backup, with fa 0/1 and fa 0/2 as the primary

interface and backup interface, set the bandwidth preemption mode and 40s preemption delay:

Ruijie(config)# interface fa 0/1

Ruijie(config-if)# switchport backup interface fa 0/2

preemption mode bandwitdh

Ruijie(config-if)# switchport backup interface fa 0/2

preemption delay 40

Related

Commands

Command

Description

show interface switchport backup

Displays the dual link backup configuration.

Platform

Description

N/A.

«
...
1382
1383
1384
1385
1386
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды