Ruijie RG-S29 Series Скачать руководство пользователя страница 773

Страница: 773 / 1510

Command Reference

OSPFv2 Commands

The spf-holdtime parameter indicates the minimum interval between two SPF calculations. Then, the

interval of the consecutive SPF calculations is at least twice as the last interval until it reaches to

spf-max-waittime. If the interval between two SPF calculations has exceeded the required value, the

SPF calculation will restart from spf-holdtime.

Smaller spf-delay and spf-holdtime values can make the topology converge faster. A greater

spf-max-waittime value can reduce the system resource consumption of SPF calculation. Those

configurations can be flexibly adjusted according to the actual stability of the network topology.

Compared with the timers spf command, this command is more flexible. It speeds up the SPF

calculation convergence, and reduces the system resource consumption of SPF calculation due to

the topology change. To this end, the timers throttle spf command is recommended.

The value of spf-holdtime cannot be smaller than the value of spf-delay, or the value

ofspf-holdtime will be set to be equal to the value of spf-delay;

The value of spf-max-waitime cannot be smaller than the value of spf-holdtime, or the value of

spf-max-waittime will be set to be equal to the value of spf-holdtime automatically;

The configurations of the timers spf command and the timers throttle spf command may

overwrite each other.

If both the timers spf command and the timers throttle spf command are not configured, the

default value of the timers throttle spf command is used.

Configuration

Examples

The following example configures the delay and holdtime and the maximum time interval of the OSPF

as 5ms, 1000ms and 90000ms respectively. If the topology changes consecutively, the SPF

calculation intervals are: 5ms, 1second, 3 seconds, 7 seconds, 15 seconds, 31 seconds, 63 seconds,

89 seconds, 179 seconds, 179+90seconds…

Ruijie(config)# routerospf20

Ruijie(config-router)# timersspf 5 1000 90000

Related

Commands

Command

Description

show ip ospf

Displays the configuration information of OSPF

timers spf

Configures the SPF calculation delay. This

command is supported in versions earlier than

RGOS 10.4. It is recommended to replace the

timers spf command with the timers throttle spf

command.

Platform

Description

N/A

2.67 two-way-maintain

Use this command to enable the OSPF two-way-maintain function. Use the

form of this command

to disable this function.

two-way-maintain

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды