Ruijie RG-S29 Series Скачать руководство пользователя страница 284

Страница: 284 / 1510

Command Reference Interface Commands

trunk

Configures the switch port as a trunk port.

Defaults

The default is

access

Command

Mode

Interface configuration mode.

Usage Guide

If a switch port mode is access port, it can be the member port of only one VLAN. Use

switchport

access vlan

to specify the member of the VLAN.

A trunk port can be the member port of various VLANs defined by the allowed-VLAN list. The

allowed VLAN list of the interface determines the VLANs to which the interface may belong. The

trunk port is the member of all the VLANs in the allowed VLAN list. Use

switchport trunk

to define

the allowed-VLANs list.

Configuration

Examples

The following example specifies a L2 interface (switch port) mode.

Ruijie(config-if)# switchport mode trunk

Related

Commands

Command

Description

switchport access

Configures an interface as a statics access

port and assigns it to a VLAN.

switchport trunk

Configures a native VLAN and the

allowed-VLAN list for the trunk port.

Platform

Description

N/A

1.36 switchport protected

Use this command to configure the interface as the protected port. Use the

form of this command

to restore the default setting.

switchport protected

no switchport protected

Parameter

Description

Parameter

Description

N/A

Defaults

This function is disabled by default.

Command

Mode

Interface configuration mode.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды