Ruijie RG-S29 Series Скачать руководство пользователя страница 281

Страница: 281 / 1510

Command Reference Interface Commands

Defaults

This function is disabled by default.

Command

Mode

Global configuration mode

Usage Guide

After this command is configured, all interface indexes are saved in the configuration file. After the

device is restarted, interface indexes remain the same as before.

Configuration

Examples

The following example enables the interface index persistence.

Ruijie(config)# snmp-server if-index persist

Related

Commands

Command

Description

N/A

Platform

Description

N/A

1.32 speed

Use this command to configure the speed on the port. Use the

form of this command to restore the

default setting.

speed

[

10 | 100 | 1000 | auto

]

Parameter

Description

Parameter

Description

The transmission rate of the interface is 10Mbps.

100

The transmission rate of the interface is 100Mbps.

1000

The transmission rate of the interface is 1000Mbps.

auto

Self-adaptive

Defaults

The default is

auto

Command

Mode

Interface configuration mode.

Usage Guide

If an interface is the member of an aggregate port, the rate of the interface depends on the rate of the

aggregate port. You can set the rate of the interface, but it does not take effect until the interface exits

the aggregate port. Use

show interfaces

to display configuration. The rate varies by interface types.

For example, you cannot set the rate of a SFP interface to 10M or 100M.

Configuration

Examples

The following example sets the speed on interface gigabitethernet 1/1 to 100Mbps.

Ruijie(config)# interface gigabitethernet 1/1

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды