Ruijie RG-S29 Series Скачать руководство пользователя страница 703

Страница: 703 / 1510

Command Reference

OSPFv2 Commands

The costs of OSPF interfaces on several typical lines are as follows:

64Kbps serial line: The cost is 1562.

E1 line: The cost is 48.

10M Ethernet: The cost is 10.

100M Ethernet: The cost is 1.

If you run the

ip ospf cost

command to configure the cost of an interface, the configured cost will

automatically overwrite the cost that is computed based on the auto cost.

Configuration

Examples

The following example configures the reference bandwidth as 10 Mbps.

Ruijie(config)# routerospf1

Ruijie(config-router)# network

172.16.10.0 0.0.0.255

area0

Ruijie(config-router)# auto-costreference-bandwidth10

Related

Commands

Command

Description

show ip ospf

Displays the OSPF global configuration

information

ip ospf cost

Sets the cost value of the OSPF interface.

bandwidth

Sets the interface bandwidth. This setting does

not affect data transmission rate.

Platform

Description

N/A

2.10 capability opaque

Use this command to enable Opaque LSA. Use the

form of this command to disable this function.

capability opaque

no capability opaque

Parameter

Description

Parameter

Description

N/A

Defaults

Opaque LSA is enabled by default.

Command

Mode

Routing process configuration mode.

Usage Guide

N/A

Configuration

Examples

The following example disables Opaque LSA capability.

Ruijie(config)# router ospf 1

Ruijie(config-router)# no capability opaque

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды